Below is a list of everyday terms and key phrases made associated with table saws as well as woodworking overall.
Know more about these woodworking terms for constructing, altering or managing your table saw.
Bevel Cut ? A cutting procedure made with the blade at any angle aside from 90 to the table top.
Arbor ? The metal shaft that connects the saw blade, extending from the drive mechanism.
Anti-Kickback Pawls ? A device which, if accordingly installed and serviced, is created to prevent the workpiece from being thrown back to the front of the saw during a ripping operation.
Blade Guard Assembly ? Metal or plastic protection appliance that is attached over the blade. Its function is to avoid the user contacting the blade.
Compound Cut ? This is achieved when a cross cut is produced making use of both a bevel angle as well as a miter.
Cutterhead ? This is a spinning cutterhead which has flexible knives or even blades. Material is taken away from the material by using the blades or knives.
Dado Blade ? One blade or collection of blades employed to cut rabbets and grooves.
Dado Cut ? A cutting process employing a dado blade, cutting a flat bottomed groove in to the face of the workpiece.
Cross Cut ? A procedure of cutting or shaping completed across the width or perhaps the grain of the material.
Featherboard ? Safety appliance employed to retain the workpiece against the rip fence and against the table top.
FPM or SPM ? Strokes per minute or feet per minute, indicating blade movements.|It means the movement of the blade in feet per minute or strokes per minute.
Freehand ? Conducting a cut without the material being led by a fence, miter gauge, or other device.
Gum ? A wood residue that is sticky and sap-based.
Kerf ? The gap or ensuing cut within the material during the cutting procedure.
Kickback ? A case where the material is propelled back to the operator at great speed.
Miter Cut ? A cutting operation created with the workpiece at any angle towards the blade aside from 90 degrees.
Heel ? Alignment of the blade in relation to the fence.
Non-Through Cut ? Conducting a cut when the blade doesn?t cut through the depth of the material.
Parallel ? Having equivalent length apart at every point alongside two given planes or lines. For example, the rip fence face is parallel to the face of the saw blade.
Perpendicular ? Intersecting lines or planes forming right-angles. For example, the blade is perpendicular to the table top.
Throw-Back ? When the workpiece is fallen in the blade or set inadvertently touching the blade, the throwing back of a material is made.
Push Blocks ? Application designed to hold the material during cutting operations. This aid helps keep the operator?s hands well away from the blade.
Push Stick ? Security tool utilized to thrust the workpiece through a cutting process. Used most often when rip cutting thin materials. The aid helps to keep the users hands properly off the blade.
Rabbet ? Cutting operation that creates an L-shaped channel on the edge of the workpiece.
Resaw ? A cutting procedure to decrease the thickness of a workpiece to produce leaner parts.
Pilot Hole (drill presses) ? Drilling a little hole into a workpiece and using it as a guideline for drilling larger holes properly.
Worktable ? Surface where the workpiece sits while conducting a cutting, drilling, planing, or sanding operation.
Resin ? A hardened gluey, sap-based element.
Revolutions Per Minute (RPM) ? The number of spins done by a rotating object in a minute.
Straightedge ? A tool utilized to verify the flatness, parallelism, or consistency of a surface(s).
Rip Cut ? Cutting operation where the rip fence is used to cut across the length of the workpiece.
Riving Knife/Spreader/Splitter ? Metal plate positioned at the rear of the blade. It maintains the kerf opening in the wood when doing a cutting procedure.
Saw Blade Path ? The spot above, below, behind, or maybe in front of the blade. The area that will be cut or was already cut from the blade.
Set ? The outward bend (or set) distance of the tip of the saw through the face of the table.
Snipe (planers) ? Depression produced at either end of a workpiece by cutter blades if the material isn?t properly supported.
Thin Kerf Blade ? A blade that has a kerf or thickness which is thinner than a regular blade.
Through Cut ? A cut where the blade cuts completely through the width of the workpiece.
Workpiece or Material ? The object where the task is being carried out.
To be more informed about the top table saws for sale that best suit your needs, visit Ed Richards? site to browse through the most highly rated table saw reviews available on the internet.
Tags: carpentry, DIY, Home & Family, power tools, table saws, woodworking
ketamine tracy morgan ground hogs day 2012 goundhog day punxsutawney facebook ipo facebook ipo
No comments:
Post a Comment